Learning the Basics of Plumbing for Bathtub Installation
Learning the Basics of Plumbing for Bathtub Installation
Blog Article
Just how do you feel on the subject of How to Install a Bathtub Yourself?
Mounting a bath tub isn't specifically brain surgery, however it does call for solid plumbing, woodworking, and also often, tiling abilities. Changing an old bath tub with a brand-new one is additionally a moderately hard task. If the old bathtub is easily easily accessible, the job can relocate immediately; if you have to open a wall to remove the old bathtub and also place the brand-new tub, the job is a lot harder. In either instance, the project is within a residence handyman's abilities, although you will require an assistant to leave the old tub and also set in the brand-new one. See to it you have qualified on your own for the work and also are comfortable trying it. As opposed to hiring a contractor to take over a halfway-completed job, it is much better to think about utilizing one prior to you begin. Opportunities are you may require an expert plumber to make tube connections.
This short article will aid you set up a brand-new bath tub in your shower room if you have already gotten a new tub as well as do not require to alter the setup of your previous water supply pipes.
Your devices and also material checklist ought to comprise the following:
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your setup, then the first thing you need to do is detach the water supply. After doing so, activate the taps to drain pipes any type of water remaining in the system. The procedure of removing the existing faucets can be quite bothersome because of the restricted access that is commonly the instance.
Use a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the faucets. Have a cloth ready for the continuing to be water that will originate from the pipes. Once the supply pipelines have actually been removed, use the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary taps from transforming during this process. When the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old securing substance.
Before going on to fit the new faucets, contrast the pipe links on the old taps to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will need a plastic port to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and the other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, then you will need decreasing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, place the tap in the placing opening in the bath/basin guaranteeing that the washers remain in place between the faucet and the sink. Secure the faucet in position with the supplier given backnut. As soon as the faucet is firmly in position, the supply pipes can be attached to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical tap ports. The former type should be connected to the tap finishes first, tightening up just by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Installing the Tub
Utilizing the two wooden boards under its feet, position the bath tub in the called for placement. The wood boards are practical in uniformly spreading the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four little points.
The following objective is to ensure that the bath tub is leveled all round. This can be achieved by examining the spirit level and readjusting the feet on the bathtub up until the level reviews degree.
To mount faucets, fit all-time low of the outermost adaptable tap adapter to the proper supply pipeline by making a compression join; then do the very same for the various other faucet.
Switch on the supply of water and also inspect all joints and also brand-new pipework for leakages as well as tighten them if needed. Load the bath tub as well as likewise check the overflow electrical outlet as well as the typical electrical outlet for leaks.
Ultimately, repair the bath paneling as defined in the manufacturer's instruction manual. Tiling as well as sealing around the bathtub must wait till the bathtub has been utilized at least once as this will certainly resolve it into its final position.
Planning for the Installment
To start with, the supporting frame provided with the bathroom needs to be fitted (if called for) according to the maker's guidelines. Next, fit the taps or mixer to the tub. When suitable the tap block, it is necessary to make sure that if the tap includes a plastic washer, it is fitted between the bath and also the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the taps system to prevent stress on the tub.
Fit the flexible tap connectors to the bottom of the two faucets using 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet with the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you utilize every one of the provided washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be suited its last position.
Tiling Around the Bathtub
In the location where the bathroom meets the tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the fitting can move enough to crack a stiff seal, causing the water to penetrate the wall surface between the bath and the tiling, leading to complications with moisture and possible leakages to the ceiling below.
You can select from a range of coloured sealants to assimilate your components and also fittings. They are marketed in tubes and also cartridges, and also can securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of soaked newspaper or soft rope. Keep in mind to always load the tub with water before securing, to permit the motion experienced when the bathtub remains in use. The sealant can break rather early if you do not take into consideration this activity before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally easily available on the marketplace. It is advisable to fit the ceramic tiles using water-resistant or water-proof adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was guided to that write-up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround from someone on a different web address. For those who appreciated our page if you please do not forget to share it. We appreciate reading our article about Tools You Need to Install a New Bathtub .
Professional-grade solutions. Report this page